Learn About Safety Awareness For Dump Truck Tires

Why Tire Blowouts are So Dangerous

Tire blowouts are dangerous on any vehicle, but that danger escalates significantly on a tractor-trailer. First, the tire blowout can cause the truck driver to lose control of the rig, putting nearby motorists at risk of an accident.

Also, rubber and metal explode from a blown-out tire at great force and speed, which can penetrate the window of a passing car or cause the motorist to lose control of the vehicle. A truck’s tire is larger and filled with more air than a car’s, making the explosion that much more violent and hazardous.

Tire scraps cause continued hazards on the road. Motorists are forced to swerve around the debris, and may spin out of control if they accidently run over it. For this reason, the trucking corporation has a responsibility to immediately clean up the debris from an exploded tire and may be held liable for failing to do so.

Poor Maintenance of Truck Tires

A tire blowout should never happen if the trucking company and driver maintain the truck. Mistakes that lead to a tire blowout include:

  • Over-pressurization of the tire: This might happen because of an incorrect gauge reading
  • Overheating: Trucks that travel to hot environments are at risk of tire blowout, especially if the tire was filled to capacity in a cold environment
  • Zipper failure: The tire can unravel if damage results in a crack or weakness
  • Demounting: An improperly mounted tire might suddenly, violently fly off
  • Threadbare tire: Tires should always be replaced before they become worn out and dangerous

Accidents from Tire Delamination

Tire delamination happens when the tread or rubber separates from the tire causing the tire to blow out or deflate suddenly. This can cause injury to motorists in many ways:

  • The truck driver could lose control of the truck and cause an accident
  • During an accident, debris from the delaminated tire can strike a motorist
  • The debris from the delaminated tire can end up in the roadway and create an obstruction that causes an accident.

After an 18-wheeler has experienced a tire blowout or delamination, both the truck driver and motorists on the road are in danger. Because the tire delamination typically causes a sudden change in stability to the vehicle, it is very difficult for the truck driver to maintain control of the 18-wheeler after this has happened. Often the motorist cannot get out of the path of the 18-wheeler and the 18-wheeler driver is unable to steer the truck to avoid hitting the motorist.

Motorist can also be injured if the 18-wheeler’s tire delaminates and rubber from the defective tire flies off and strikes a car. Often, when a tire blows out or delaminates, pieces of the tire become airborne when the driver frantically tries to maneuver the 18-wheeler to a safe location or out of the flow of traffic. These airborne pieces of rubber can be large, sharp, and hot from the friction of the road. Tragically, they can injure a motorist or pedestrian if they are struck by the flying rubber.

How to Fix a Flat Tire

Having a flat tire is one of the major inconveniences of driving. When a good spare is unavailable, you either have to call a tow truck or fix the tire yourself. Luckily, the process of fixing it yourself is relatively straightforward and requires only a few tools.

Finding the Leak

  • Inflate the tire.

In order to find a leak the tire must be properly pressurized. You should inflate your tire with air until it reaches the appropriate pressure (measured in psi) specified in your vehicle’s service manual.

  • Visually inspect the tire.

Before moving on to more time consuming techniques, you should take a moment to look at your tire. If you notice any holes, cuts, or objects protruding from tire then you have found your leak.

  • Listen for a hissing sound. Even if you aren’t able to see the problem right away you might be able to hear it. A hissing sound is a clear sign that air is leaking from your tire, and can help you locate the leak.
  • Feel around the tire for air.

 If you run your hands over the tire carefully you may feel the leak even if you can’t hear or see it.

  • Mix soap and water.

If you followed the steps above and you were not able to easily find the leak don’t fear. Spraying the tire with a little soapy water or window cleaner may help. If you see bubbling at any place on the surface of the tire then you have found your leak.

  • Cover the tire with the soap and water solution.

You can use a spray bottle to spray the tire, or if a spray bottle isn’t available you can just pour the mixture over the tire.

  • Watch for bubbles.

As air escapes the tire and encounters the soapy water mixture it will form soap bubbles. If you notice the soapy water bubbling at any particular place on the tire, you have found your leak.

Fixing the Leak with Tire Puncture Sealants

  • Read the directions on the can of sealant you have brought.

Various manufacturers have slightly different steps and required amounts you should put in. However, there are some steps that are generally the same.

  • Pull out any object that has punctured your tire.

This may or may not be necessary depending on why your tire is flat.

  • Turn the wheel until the valve is at the top of the wheel.

Unscrew your valve cap. You will put the sealant in the same way that you would inflate your tire with air.

  • Attach the nozzle of the product to the valve stem.

Once you have it on securely, press a button to release the contents.

  • Drive your car.

You need to drive your car to rotate the tire. This allows the sealant to be distributed evenly inside the tire and prevents it from forming a heavy lump inside the tire.

  • Replace your tire.

Tire sealants are great to bail you out in a major crisis. Unfortunately they are only good for 3 days or 100 miles, whichever comes first. You should replace your tire before then to avoid possible problems.

Bathroom Remodeling Is the Latest Trend That Is Catching Up Fast With Urban Homes

Crucial Questions to Ask Before a Bathroom Remodel Begins

So you want to remodel your bathroom? Then congratulations and a fair warning are both in order. Because whether you’re simply upgrading your sink or ripping out every last tile, it takes tons of research to get a successful bathroom renovation right.

How much can you spend?

The average bathroom remodel will cost $20,420, but that will vary widely, based on what you do. Even a simple toilet can range from hundreds to thousands of dollars. “On average, you should budget $10,000 to $30,000,”

Who will be using the bathroom?

Consider who will be using the bathroom to help you whittle down your choices. For instance, if kids will be using the bathroom, you’ll definitely want a tub, or tub/shower combo. A tub is also key feature when it comes time to resell—at least for buyers with families.

Do you want a bigger bathroom or one the same size?

The average bathroom is 40 square feet, which may be cramped if you dream of an expansive oasis. If you want to expand, you probably can. But it will mean moving walls, downsizing adjoining rooms, or carving out space from closets.

Are you changing fixtures and/or location?

Where you want everything located is important—and moving things can cost a pretty penny. “Many clients wish to change a fixture location, such as possibly moving a toilet to a new area in the room,”

Bath Renovation Costs

These costs end up being higher for than the national average*.

Minor, mid-range renovation: Starting at $18,000—$25,000

Mid-range renovation: Starting at $29,585

Upscale renovation: Starting at $50,000—$60,000

Remodeling an bathroom all at once

While it can be tempting to apply à la carte prices to individual elements of the work, a full bathroom renovation is an integrated process that involves design, materials, installation, and plumbing. If your bathroom has one or two areas of concern, you might decide to swap out an individual fixture or two. You can replace a toilet or vanity or take on some limited retiling and pay solely for the cost of the new fixtures and the hours of installation work.

Low to high-end costs for bathroom materials and finishes

These are the visible parts of a bathroom renovation, and probably the aspect you’ve spent the most time thinking about. Take a look at the range of pricing for various fixtures, materials, and finishes in the chart below

How much will materials for a bathroom remodel cost?

Wall and floor tile: Low-end – $3 per square foot (psf), Mid-range – $15 psf, High-end – $35 psf

Sink: Low-end – $50, Mid-range – $150, High-end – $500 and up

Vanity: Low-end – $250, Mid-range –  $1,000, High-end – $2,000 and up

Sink and shower fixtures: Low-end – $40/fixture, Mid-range – $100/fixture, High-end – $350/fixture

Bathtub: Low-end – $150, Mid-range – $600, High-end – $2,000 – $3,000

Shower enclosure: Low-end – $350, Mid-range –  $1,000, High-end – $2,000

Toilet: Low-end – $150, Mid-range – $400, High-end – $1,000 and up

Medicine cabinet: Low-end – $50, Mid-range – $150, High-end – $500 and up

Accessories (hooks, towel bar, paper towel holder): Low-end – $10/item, Mid-range – $50/item, High-end – $100  and up

Lighting: Low-end – $25/fixture, Mid-range – $150/fixture, High-end – $300 and up

Ceiling vent: Low-end – $50, Mid-range – $200, High-end – $500 and up

Radiant floor heating: Low-end – $6 psf, Mid-range – $8 psf, High-end – $12 psf

Building requirements

For those in apartments, building requirements can play a significant role in dictating design and budget needs. These requirements can range from insurance coverage minimums, which limit your ability to work with professionals who aren’t carrying high-value insurance policies, to general alteration agreements that require anyone doing any work in the building to have far-reaching coverage for problems they may never encounter, like asbestos removal or collapse scenarios.

The Ultimate Guide to a Bathroom Remodel

A bathroom remodel can be difficult, stressful, and expensive. Use this guide to prepare yourself and get the best bathroom remodel possible. From sketching out ideas to choosing the right contractor to the punch list.

Deciding what you want to do

If you’re considering remodeling your bathroom, you’ve already begun the pre-pre planning phase whether or not you realize it yet! Before you rabbit trail too far into the weeds, take a moment to ask yourself some important questions to help direct your planning.

Why do I want to remodel my bathroom?

What inspired me to consider remodeling my bathroom?

How long do I plan to live in my home? (Do I want to remodel for my enjoyment or for resale value?)

What do I love about my current bathroom?

What do I most want to change about my current bathroom?

Collecting Your Ideas

We’re not talking about polished ideas of exactly what you want here, we’re talking raw materials that are going to come together in one glorious plan for your bathroom remodel. Even if the picture or idea you have isn’t directly related to bathrooms, but speaks to the style you want for your bathroom, just start collecting!

A final thought on collecting ideas

If there are two of you involved in this bathroom remodel, get ideas from both partners and put them together in the folder or Pinterest board. Better yet, go out on a date once you’ve compiled your ideas and share with each other!

A Homeowner’s Guide to Bathroom Remodeling

A beautiful bathroom—whether it’s your downstairs half-bath, a small powder room for visitors, or your own luxury master bathroom in your own bedroom—is always a highlight of any home’s floorplan. For homeowners with older homes or newer ones made with cheaper, less-efficient, or high-maintenance materials, you may have noticed how difficult it is to keep your bathroom looking clean and modern.

Hard-to-maintain bathroom spaces can detract from the value of a home’s aesthetics, affecting its functionality and asking price—if you’re thinking of selling. Bathroom remodeling is an excellent option for homeowners hoping to upgrade their homes with some of the latest in new technology, to take advantage of the incredible materials and products made specifically for renovating old bathrooms into gorgeous, gleaming ones.

While bathroom renovations are known to offer some of the highest returns on your investment available in home remodeling—planning your project to the tiniest detail is of the utmost importance. Another major factor in getting the superior results you want (and enhancing your home’s value to the fullest degree possible) is the contractor you choose to perform the work you want.

Important Details to Consider Before Getting Started With Bath Renovation

Whether you’re the type of homeowner that likes to jump in headfirst, or if you’re more of the type that’s likely to drag your feet a bit getting started, taking the time to plan a bathroom remodeling project is the key to its success. A badly planned home renovation can end up in a costly disaster—so it makes sense to take things a bit slow, at least at first, and make sure you’re covering your tracks from A to Z right from the beginning.

Types of Bathroom Remodeling Projects

As we mentioned in the last section, there are many types of bathroom remodeling projects to choose from. Deciding on the type of project you want for your home depends on your own goals for improvement—and what you hope to achieve with a renovation.

Bathroom Remodel Guide

You may have your living room well furnished with fascinating artworks and décor, your kitchen well furnished to taste with the state of art amenities, but have you ever thought of remodeling the bathroom?

Your friends, family or any other guest visiting your apartment for the very first time may ask for a tour, after showing off your well-furnished living room and kitchen room, how will you react when asked of the bathroom- given you are yet to remodel it?

The bathroom is the room for high personal hygiene activities, a place you start and finish each day with; when you wake up, you use the washroom to wash your face, brush your teeth, your hands and prepare to leave for work or go to bed. An average person spends over 400 days of his or her lifetime in the bathroom

No doubt the situation of your bathroom is the final yardstick in judging the type of person you are when your home is subjected to a tour. To scale through this, you should consider getting in touch with bathroom remodel contractor near you and get a good bargain of the cost of remodeling the bathroom.

Future prospect

When considering a bathroom model, whether to go for the bathtub or shower-only option, consider how many baths you take a year. Always bear in mind that you are renovating your home for yourself first and for a future buyer second. Go for the top-notch permanent features. Even if you have only been living in your house for a few years, it is worth doing it yourself. Selecting the best durable features will save you from unnecessary future expenses in additional remodeling.

What Exactly Is Electronic Leak Detection

Water Leak Detection

Some of the equipment that might be used would be line location equipment to be able to locate where the lines are running underground or the slab and/or several types of high powered listening devices to listen for air (that would be pumped into the water system), water and/or mixture of both escaping from the pipe through the leak.

Locating concealed fresh water leaks is a very difficult job. Many people in industry say they can do it, but very few people can actually pinpoint a leak properly. A major key to proper leak location is having someone who does and has done many of them. The more someone does the better they will be at them

Unfortunately no one in fresh water leak detection is perfect, but the right ears and experience is the key to getting right the overwhelming majority of the time. It is important to understand that when detecting a fresh water leak usually only one leak can be found at a time. Meaning it would be necessary to find and fix one leak then re-test the system to see if there are any further leaks.

However, do believe that the homes that have had more than one leak over any period of time will very likely continue to have leaks within the system. With this in mind, in most cases recommend leak location and spot repair of a home’s first leak.

Although many people in industry highly recommend re-routing water pipes to the attic immediately when a leak is discovered, this is not something that recommend at all. believe re-routing should be avoided at all costs and be used only as an absolute last possible option. Putting fresh water lines in walls and attics where one leak could cause major damage to a home is in opinion a very bad idea.


Leaks are always inconvenient, and it makes no difference when the leak comes to your attention, it is clear that there is a possibility that there is a very major issue causing the leak in question. More often than not, there is more to it than observing a pool of water and then repairing a pipe situated above it which makes it necessary for you to engage the expertise of a professional service

In the event of you suspecting a leak, the best thing to do is, first of all, turn off the water at the mains in an office building before you go home from work. At the same time, it is a good idea to take a reading from the water meter. The following morning, turn on the water again and take another meter reading. Any difference in the two readings can indicate that there is a leak. Places, where the water pressure is high or inconsistent, are susceptible to a lot of breaks and leaks

can guarantee punctuality in arrival time and as a matter of courtesy, you will receive a telephone call when skilled staff are making the journey to your home. All the plumbers employ have police clearance and are fully competent for the job. All the required tools and equipment are stocked in service vans so that most plumbing repairs are possible to do in your home without needing to look for supplies.


Water pipe leaks are an increasing cause of homeowner insurance claims today thanks to continuous usage of aging systems.  Corrosion that takes hold in your water systems can lead to systemic damage, cracking, pipe bursts and eventually flooding.  Getting to these leaks in their infancy is crucial if you’re to minimize the structural and financial impact water leaks can cause

techs are water system experts capable of finding leaking components throughout your property’s systems. use a variety of testing processes including odor detection, visual inspections, thermal imaging of walls, foundations and more, to identify degraded piping elements. can even detect water main leaks that may be impacting the water supply throughout your entire piping system.

What is Leak Detection?

The sound of running water when no water should be running – you could have a slab leak

A warm or hot spot on the floor could be the indication of a hot water slab leak

If you observe cracks in the wall, doorways or floors it could be damage resulting from a slab leak

Mysterious moisture, excessive moisture or mildew under carpets, vinyl floors and walls could indicate a slab leak

High water bills could also indicate a slab leak, or a leak in your irrigation, pool or plumbing under the slab.

Water Leak FAQs

If you have questions about leak detection, have the answers! goal is to give customers all of the information they need pertaining to water leaks and leak detection so they get a good understanding of the products and services offer them.

How does a leak detector work?

A pipe or area with no leak sounds different than a pipe or area that has a leak or leaks. Smaller leaks emit a sound that is too high of a frequency for people to hear, and this is where leak detectors come in. Certain leak detectors take this sound and convert it to a level you can hear through a pair of headphones. As you get closer to the leak, the sound gets louder.

The Plumbers Complete Leak Detection Kit

Launching a career in Plumbing Leak Detection or adding leak detection services to an established business is easy with the equipment in the Plumbers Leak Detection Kit. Wherever the leak is on the customer’s property, you’re going to find it accurately, and fast! Don’t call someone else to take care of YOUR client. perform an end to end leak detection on your own using the equipment in the Plumbers Kit. It’s everything you need to take the call and get the job done right.

The heart of all kits, including the Plumbers Leak Detection Kit, is the LT-1000 Amplifier. research and development team has engineered this phantom powered device to deliver highly sensitive listening capabilities and works to power all the listening technologies you’ll find in the Plumbers Kit.

start leak detection at the meter. If can see the meter spinning, confident water is moving through the house. it is important to have all devices off in the house. No running eater, no running toilets, washing machines, dishwashers, showers or sinks. Turn everything off in the house. If the meter is still spinning, it’s virtually guaranteed the customer has a leak

Now, shut the water main into the house. If the meter is still spinning, a leak is between the meter and the house – though a leak may still exist in the house itself. If it’s not – we have a leak further back on the property, in the house. This is where the listening equipment in the Plumbers Kit takes the stage.

Customers call for a number of reasons. They hear water running, they see a visual confirmation of a leak or they see a spike in their utility bill. Wherever the cause of these issues lies, you’ve got the equipment to accurately find those leaks and get paid.

Leak Detectors

Leak detectors use a variety of technologies to quickly identify and locate small leaks in enclosed gas systems, increasing system performance and eliminating safety hazards. Most all leak detectors use one of the three leading sensing technologies; heated diode, solid-state, and ultrasonic.

Ultrasonic Inspection System

Digital system for mechanical and electrical inspections, leak detection, energy audits, vibration testing, and more.

Gas Leak Monitor

Superior performance, flexibility & functionality for low level continuous monitoring of refrigerant gases used in most commercial systems .

Wireless Totalizing Transmitter

Measure average flow and totalized volume, simple connection to a turbine meter or a pulse output device.

Acoustic Imaging Camera

Detects and displays leaks in compressed air systems and partial discharge problems in high voltage electrical systems.

Leak Detector

Allows pinpoint detection of both refrigerant and combustible gas leaks with the same instrument.

Pitched Roof VS Flat Roof

When your flat roof needs to be replaced

The Three Types of Flat Roofs

At the heart of any flat roof installation is deciding on the type of roof that best fits your home style, intended use, climate, and budget. The three main types of materials and methods used in installing flat roofs offer homeowners a variety of benefits and disadvantages.

Built-up Roof

The most traditional method, the built-up roof consists of several layers of materials that are laid down atop each other, including hot tar (bitumen), gravel, fiberglass, and roofing felt. This type of roof is fire-resistant thanks to the layers of gravel and can last up to 30 years. However, because of the hot tar, the installation of this type of flat roof should always be done by a professional roofer. It is also a very smelly process and is not recommended for occupied homes. The average cost of a built-up roof installation is $3.50-$7 per square foot.

Modified Bitumen

In direct contrast to the layered approach of the built-up roof, the modified bitumen system utilizes only one layer of rolled material, which can be made of various compounds and installed one of two ways.

The traditional installation, known as torch-down application, requires installers to heat the materials on the roll as they lay them down on the roof. A layer of felt is applied to the roof, followed by a primer and the strips of bitumen, which are sealed onto the roof via the flame of a large torch.

Because this is highly specialized and presents a fire hazard, torch-down modified bitumen roofs are rarely used outside of the professional realm. By contrast, the more modern modified bitumen approach, called peel and stick, is a possible DIY project. Both types of modified bitumen roofing systems are notable for their light colors that reflect heat, their up-to-30-year lifespan, and their middle-grade price. In fact, the installation of a modified bitumen roof generally costs between $3-$6 per square foot.

Rubber Membrane

Made of “true rubber” or ethylene propylene diene monomer (EPDM), the rubber membrane roof is literally like a flattened car tire. However, the chemistry of the material is such that this type of roof actually resists sun damage. It is also lightweight, resistant to scuff marks and tears, and relatively easy to patch in the event of a leak. EPDM roofing is available in two colors—black and white—which serve the needs of different climates and budgets. While the black variety absorbs quite a bit of heat, the white material costs 30 percent more on average because of its heat-reflecting properties. While the average cost to install EPDM roofing is between $4-$6 per square foot, it is easy to install EPDM roofs yourself because there are several systems that you can use to secure them according to your skill level and comfort. This includes mechanical anchoring with fasteners or adhesive anchors or ballasting the material with stone.

Common flat roof problems leading to replacement

If you see the following indications, be sure that minor roof repair won’t be enough.

Water Pooling

One of the biggest issues flat roofs face is pooling water, which can result in irregular stress that causes cracks. Over time, the roof may shift a bit, meaning it may not be as level as it was when it was installed. This will most likely result in water pooling in dips and divots. While flat roofs are manufactured to stand up to water, these pools need to be drained as soon as they form to ensure water doesn’t seep into the roof’s layers. When left unchecked, the pools will harm the roof’s surface and shorten its lifespan.

Bubbling, Blistering and Adhesion Failure

Bubbling and blistering are defects that typically result from adhesion failure. The visible bubbles are generally filled with water or air. This could be a result of poor workmanship, bad insulation or insufficient ventilation. When caught early, the problem can be dealt with; left untreated, the blisters will get too large to be fixed. They can later pop and leave holes in your roofing that make your property vulnerable to interior damage. The cause behind this could be that the roof had excess moisture when it was installed.

Moisture and Leaks

Flat roofs face lingering moisture issues that can be handled effectively so long as you stay on top of them. This type of roof, like any other, can leak, as the water doesn’t have anywhere to go but down. This results in moisture seeping into the roof membranes, leading to further problems such as fungus and mould. The best way to deal with leaks and moisture is to have your roof inspected and maintained regularly. If problems aren’t caught early, a professional roofing company will be able to advise you on the best course of action.

Cracks, Splits and Tears

This is perhaps the easiest problem an untrained eye can spot. If a crack or split is left for too long on a flat roof, the plyboard or chipboard will absorb water. This may turn the material to mush so it becomes uneven, making the roof unsafe to walk on and preventing it from functioning at its best. You may choose to have your roof repaired if the problem isn’t extensive.  However, if you notice cracks or splits across the whole surface, it’s best to replace it.


Similar to other materials, flat roofs with asphalt expand and contract with changes in temperature and weather. When left unchecked, this expansion and contraction will cause the flashing to pull away from the corners and edges of the roof, leading to moisture getting trapped and leaks appearing on your ceiling. Failing to address the issue promptly will deteriorate your roof’s flashing, compelling you to replace it.

Organic Growth

Although algae, lichens and moss might not seem like big problems, they signify that your flat roof requires attention. Any kind of organic growth on your roof is indicative of unwanted water retention. Left untreated, it can do extensive damage to your building. If you can’t figure out why there’s organic growth on your roof, have it checked by a professional.

Damaged Top Coat

If you can constantly hear a fluttering sound coming from your roof during windy conditions, chances are the top coating is damaged. As a result, every time it rains or snows the fluttering panels will expose the materials underneath to weather and cause damage. Not addressing this issue could mean that the roof fails completely and causes weather or water damage.

Design and installation

If you have had a modified bitumen felt roof installed for over 20 years, you have benefitted from an extremely exceptional lifespan for this type of roof. One would imagine that it must have been installed with a lot of care and attention and been subject to minimal foot traffic during its lifecycle.

It’s not uncommon for a felt roof to last only just over two years before it needs to be replaced. For many homeowners who opt for a felt roof, they can feel as though they have found themselves with a leak no sooner than they have had the roof installed.

If the roofer cuts back on materials, time or effort when installing a flat roof, this could significantly compromise the roof’s long-term resilience and reliability. Many homebuilders even prefer to forgo flat roofs and instead choose a tiled pitched roof for lower-level extensions and garages.

Indeed, a pitched roof can be guaranteed for longer than many types of flat roof, while a good provider of flat roofs can be a lot trickier to find than a tiler. Therefore, what are the key signs to look for when diagnosing a flat roof? How would you know whether it needs replacing or repairing?

Here is a list of particular defects that could call for a flat roof replacement. However, keep in mind that, in nearly any of these circumstances, it would be advisable for you to call in a professional to survey the roof before you have a new roof installed, as the issue might be minor.

How do you decide?

When it comes to the dilemma of repair or replace, it can be tough figuring out the best course of action. In the short-term, it is usually going to be cheaper to repair the roof. On the other hand, if your roof is bad enough, continuing to repair it becomes a never-ending exercise in futility. And you can easily end up spending more on repairs than you would have spent to just replace the roof entirely.

A good rule of thumb is this: if the material with which your roof was constructed has reached the end of its service life, you should probably replace it instead of repairing it. It is only a matter of time until other problems develop. In addition, if the cost of repair is going to exceed 20% of the cost of a new roof, and if the age of the roof is more than half of the expected service life of the material with which it is constructed, you should probably replace it. The likelihood of having to pay for additional repairs in the future is high enough to justify the additional outset at the present.

Drywall Repairs Methodologies And Benefits

Supply Checklist: Everything You Need to Paint a Room

I’ve painted many rooms in my day (I’m a little bit of a painting junkie), and like so many other things, once you get the hang of the process it’s really quite fun. Throw on some old clothes, kick out the jams, and after a few hours of good old physical labor, you’ll have a wonderfully transformed space.

I’ve found that getting my supplies in order makes a big difference when the time comes to start painting. Having all prep and paint supplies at the ready cuts down on frustration and helps the process move along more quickly. If you’re getting ready to start your own painting project, here’s a supply checklist that should cover everything you’ll need.

Prep Materials

Before getting to the fun part, it’s important to spend a few hours prepping your walls; patching holes, cleaning, and sanding are all important to achieving the best result.

• Spackle & spatula – Use to patch any holes.

• Metal paint scraper – Use to scrape off any peeling or cracking paint (if necessary) before sanding.

• Fine grit sand paper – Use to even out rough texture and smooth down any bumps.

• Mild soap & water solution – Use to clean any dirt or grease off walls before priming.

• Painter’s tape – Use to tape off borders so paint doesn’t bleed into areas you are not painting; also use painter’s tape to cover hardware and outlets. I really like Frog Tape, which I’ve found to work great to achieve clean edges.

Painting Supplies

• Canvas tarp or plastic drop cloth – Use to protect floors and furniture (if furniture cannot be moved out of the general painting area). I’ve even used old newspapers in a pinch, but wouldn’t recommend if painting in a carpeted area.

• Angled paint brush – Use to paint corners. Angled brushes help achieve clean edges without paint bleed, which can be tricky in corners if using a regular flat brush.

• 3-inch flat paint brush – Use for “cutting in”, which is the process of painting the border around the taped-off area.

• Paint roller frame & roller covers – Use a roller for the majority of painting, since it’s a much faster method than a brush. If you’re painting a large room or a room with high ceilings, I would recommend using a painter’s pole, which you attach your roller to for extended reach.

* Note about roller covers: Make sure to choose an appropriate roller cover for your project. All covers are not made the same, as some are designed for smooth wall surfaces, others for stucco or brick, and yet others are designed for extra smooth surfaces like metal.

• Paint tray – Use to hold smaller portions of paint as you work. Also useful to avoid dipping brushes directly into paint cans, which can contaminate paint with dust and dirt.

Tips for Patching Drywall

Before you paint a wall you have to prepare the surface, which inevitably involves patching. It’s one of the most important steps. But sometimes it takes more than just a can of spackling and a small putty knife to get good results. Here are some wall patching tips and products that will help you speed up the job, avoid problems and end up with a flawless wall.

Use Self-Priming Filler

Patches made with traditional patching materials need to be primed with a sealing-type primer before painting. Otherwise the patched areas could show through the finished paint job as foggy spots. But if you patch with a self-priming patching material, you can avoid this extra step. There are several brands; just look for the words ‘self-priming’ or ‘with primer’ on the container.

Use Setting Compound for Big Holes

It’s fine to fill screw holes and other small wall dings with patching compound, but for dime-size and larger drywall repairs, and for holes that are deep, it’s best to use a joint compound that sets up by a chemical reaction. These are available in powder form with setting times ranging from five to 90 minutes. The reaction starts when you mix in the water, and the compound hardens in the specified time. The five-minute version is nice because you can buy the powder in a convenient 5-lb. box, and the compound hardens quickly, so you can apply another coat right away. Remember, setting-type compounds are harder to sand than regular patching materials, so make sure to strike them off flush to the surface when you fill the hole. You’ll find setting-type compounds wherever drywall taping supplies are sold.

Make a Dent for the Patching Compound

When you remove a nail, drywall anchor or picture hanger, there is usually a little ridge of old paint or drywall sticking out that’s hard to cover with patching material. The solution is to make a dent over the hole, and then fill the dent. Most good-quality putty knives have a rounded hard plastic or brass end on the handle that works perfectly for making the dent. The rounded end of a screwdriver handle or the handle of a utility knife will also work. Press the handle against the hole and twist it slightly while applying pressure to dent the surface, or if you have good aim, use your denting tool like a hammer.

Cover Cracks with Repair Spray

Stress cracks usually show up around window and door openings. The cracks are the result of framing movement and are hard to fix permanently. But using spray-on crack repair is a good way to at least extend the life of your repair. The spray forms a flexible membrane over the crack that can stretch and relax as the building moves.

How To Repair Damaged Drywall?

You can face a lot of anxiety and challenges when repairing damaged drywall, whether it was caused by condensation from your central air conditioning, a leaky roof, or flooding, especially if this is your first time doing such. The walls and ceilings in your home are expected to be strong and solid, and making a hole into any of them should be a difficult task.

This is not actually the actual case. Although there are some preparatory works required in the process, however, you can practically make the damage disappear with a little care and patience.

Drywall is hard but not beyond destruction. With time, you can see unattractive cracks or holes on gypsum-board walls. The good news is, repair of drywall is relatively easy, but it requires an art. You will find the things to do and not do when repairing damaged drywall to make it invincible to homebuyers, landlords, or visitors.

What is Drywall?

Drywall is mainly a gypsum (calcium sulfate dihydrate) panel placed between two types of paper: one has a light-color face, and the other has a darker back. It first became popular in the United States of America in 1916 when the Gypsum Corporation in the country produced a product names “Sheetrock” aimed to be a non-warping, non-burning wall surface masking. Because the wall was widely accepted, even though it doesn’t require a wooden lathe, it was tagged as the poor man’s replacement for plaster walls.

Drying time will be required between many of the steps discussed, so you should know this repair task may require you to work for a few days. Applying thin coats and doing it step by step without rushing will give you an expert-level outcome

Tips for Flawless Drywall Repairs

Drywall may be among the most common interior construction materials, but it’s far from indestructible. Indeed, most homeowners and business owners will experience dents, dings, and holes in their drywall at some point.

Gather the Materials You’ll Need

Before you can fix your drywall, you need the right materials on hand. While not all drywall repair jobs will require everything listed below, these items cover just about any type of repair job you might encounter. You’ll want:

Joint compound/spackling paste/putty

Putty knife

Sandpaper (various grits)



Utility Knife

Tape Measure


Drywall Tape

Drywall Screws

Drywall Patch Kit

Extra Drywall Material

Paint (and roller pan)


Inspect the Damage

The exact materials you’ll need, and how you use them, will depend on the type and severity of damage done to your drywall. For instance, a minor puncture that’s just a couple inches or smaller in diameter can be easily fixed by filling it with quick-drying spackle, sanding it smooth once dry, and painting over the repair.

Push in Protrusions

Drywall damage doesn’t only include punctures and holes. In some cases, a small portion of the drywall might stick out after a fastener, nail, or picture frame hanger is removed from the surface. When this happens, you’ll actually want to make a dent of your own directly over the protrusion so you can fill it with joint compound and smooth it over. Just like that, the blemish will vanish.

Spray Over Those Stress Cracks

As the ground beneath us slowly shifts, fine cracks may appear in your drywall. These fractures can easily be fixed by coating them with a spray-on crack repair solution. This will cover up the lines and give the wall some flexibility to prevent further fracturing.

Drywall Repair: How to Repair Drywall

Clean hole with blade knife. Cut at an angle so the exterior of the hole is bigger than the interior.

Fill the hole with painter’s putty. Make it level with the wall surface.

Let it dry. Once dry, lightly sand the area until smooth.

Spackle over the putty. You may need to repeat this step.

For medium holes, use a drywall metal patch.

Sand the surface smooth around the hole.

Wipe off dust.

Peel paper backing off the patch. Firmly press patch in place with mesh facing outward.

Spread drywall compound over the patch, feathering out the edges. Smooth out and let dry

Gently sand surface until smooth with the wall. Repeat step 9 and 10 until the patch can no longer be detected.

Larger holes need patches made of drywall. Make sure it is the same thickness as the drywall already present.

Cut a square of drywall slightly larger than the hole. Score one side with a blade knife and snap it apart. Cut the back of the break line.

Draw an outline of the patch around the hole using a pencil.

Check for electrical cords and plumbing lines where you plan the cut.

Use a drywall saw to cut out the drawn area.

Screw in two wooden boards behind the drywall, one at the top and one at the bottom of the hole. This will keep the patch from falling through.

Screw the drywall patch to the wooden boards.

Spread drywall compound and add mesh.

Sand area and repeat steps 18 and 19 until the patch is undetectable.

Paint over once it’s dry.

Vinyl Flooring Can Add Beauty To Your Home

How often should vinyl flooring be replaced?

How to Know When it’s Time to Replace Your Flooring

The floors in your home bear the brunt of the wear and tear it receives. Daily, they’re put to the test of handling dirty shoes, spills, and scratches from furniture, pet claws, sweepers and more. So it’s only a matter of time before they need to be replaced. The question is: how long?


Thin laminate or vinyl tile clearly displays when it’s at the end of its life. Whether the floor has seen water damage or just simple wear and tear, if it’s peeling up that means it’s time to replace it. This shows that the adhesive is starting to fail.

If any of your flooring is due to be replaced, it’s the perfect time to consider adding in-floor radiant heating. A radiant heating system is installed between your new flooring material and the subfloor and is a great way to add value to your home.

How to patch vinyl flooring

Vinyl tile flooring: Vinyl tiles come in smaller squares that are often easy to replace. If one of your tiles is discolored or scraped, all you have to do is remove it and replace it with another matching tile. Use a putty knife to dig into the seam. Then, tap its back end with a hammer to help the tool shimmy under the tile. Carefully lift the tile, using the knife to scrape areas where it’s stuck. Once the tile is gone, remove the glue with a floor stripper. Apply the new tile.From stains to dents to lifted seams, vinyl flooring can sustain some damage over time. Luckily, it’s all rather simple to fix. The techniques you can employ to administer repairs depend on what the damage is and the kind of vinyl flooring you have.

Patching: Sheet vinyl is a little more difficult to repair than tiles, which are smaller. Sheets have a bigger surface area, so simply replacing them isn’t always an option. Instead, you can use the patching method. First, identify the damaged area and box it in with tape. Then, find a piece of vinyl not attached to your floor (leftovers from your installation) and look for a section that matches perfectly to the damaged area. Cut a square out of the floor and the replacement. Adhere the replacement in the hole you cut out. Make sure the patterns match up perfectly, or you’ll notice the patch. Additionally, use a very sharp knife and straightedge to do all the cutting.

How to restore vinyl flooring

When the finish on your vinyl flooring no longer shines, it’s time to give it a facelift. This is an easy fix, as you only have to apply new finish to your floors. Here are a few ways to revitalize your vinyl:

Refinish: If your vinyl floors have a finish on top, you can bring its shine back to life with a suitable finishing product. Floors with five or more layers of finish need to be stripped. Use a stripping solution made for vinyl floors, following the instructions verbatim. Most products will have you mop with the stripper and let the floor dry. Then you’ll scrub the vinyl with a stripping pad, apply stripper again and rinse. After that, vacuum your floors with a wet vac​, then a dry vac. Mop the new finish on your floors and let the product dry. Buff the floors between each coat.

Floor shiner: Most newer, luxury vinyl floors won’t require a drastic facelift, like refinishing. Instead, you can purchase floor products meant to deep clean and restore the surface. If your floors lack shine, you might need to adjust your maintenance habits. Stick to a pH-neutral cleaner, as alkaline solutions strip vinyl of its wax finish. Proper cleaners should help floors retain their glossy finish.

How to replace vinyl flooring

A new floor is the answer if your vinyl is past the point of no return. For example, a replacement is needed if there are noticeable rips in various areas of your floor. Or if your floor has undergone water damage which makes it more susceptible to further tears. However, the installation process for vinyl floors is relatively easy.

  • Start by removing your existing vinyl, cut it into manageable strips and pull away from the corner, using a scraper to separate the flooring from the adhesive. For especially stubborn areas, it’s best to heat the section beforehand with a heat gun or even hairdryer. This softens the adhesive making it compliant.
  • Once you’ve reached your subfloor, thoroughly clean it by sweeping away any dust or debris and allow it to dry for at least 24 hours, during this time take your new vinyl out of its packaging and allow it to acclimatise.
  • When ready, start by cutting your new vinyl to the size of your room, allowing an extra 15 cm just to be safe.
  • Then lay over the floor. The installation method depends on the room’s size. Smaller rooms can get away with a simple loose installation without glue. For rooms between 12 and 25 metres squared, use double-sided tape, we offer this in our Adhesive Section. For larger rooms, spread adhesive on the subfloor before laying.
  • Finish by adding beading with glue or a hammer and nail.

How to repair vinyl flooring

Although Vinyl flooring is one of the most durable types of floors, it sadly isn’t immune to damage. A simple repair is recommended if your problems are just minor rips or tears with smooth edges. This repair is easy to carry out yourself by simply using a vinyl floor adhesive and putty knife. But if your tear happens to be larger, have jagged edges, or be in a noticeable spot, it’s best to replace that section of flooring.

How to fix vinyl flooring minor tears

  • To fix smooth and minor rips or tears, start by cleaning up any debris or dirt. This could otherwise lead to further damage and rips after the repairs.
  • Next, gently wash the damaged area with warm water to get rid of any surface film on your floor, then dry thoroughly. At this point, you should open your windows to properly ventilate the room.
  • Next, get out your vinyl flooring adhesive and using a putty knife, spread a little under the edge of the rip.  Place firmly down on the area and then cover the rip with tape to allow it to dry properly. It’s helpful to add something heavy on top of the area to hold it all in place.
  • Then leave the rip to dry for the length of time recommended on your chosen adhesive. After this, gently remove the tape and your vinyl floor should be as good as new!

How to fix larger tears

For the sections with the bigger tears with jagged edges, this isn’t easily fixable by simply glueing down and you’ll have to replace that section of flooring.

  • To do this, start by finding a larger part of vinyl that matches your floor perfectly, either remnant from the installation or parts taken from a hidden section.
  • Tape this piece over the damaged section, ensuring the patterns align. Then use a utility knife to cut through both layers of vinyl. Try and cut so the lines will go unnoticed, for example, if it’s a tile print, cut around the edges of the tile.
  • Next, remove the damaged layer of vinyl, you may need a putty knife to break the vinyl away from the adhesive on the subfloor. Scrape off the old adhesive and then use the putty knife to apply a fresh, even layer of vinyl floor adhesive to the area of the floor.
  • Finally, firmly press your new layer of vinyl on and leave for the recommended drying time of the adhesive. It’s also recommended to use a seam roller to allow the edges to blend perfectly.

How to clean vinyl flooring

Cleaning your vinyl using only water will usually suffice. However, the best way to clean vinyl floors is to use a mild cleanser designed for vinyl floor care. Use this with a mop and water to add extra sparkle. However check the label before using, as different vinyl will require different products.

While it may be tempting to go overboard with your mopping, the best way to clean vinyl floors is to try to use water sparingly. Although vinyl flooring is not as prone to damage as solid wood, too much liquid does not benefit it. An overly wet mop could work its way into the seams of the vinyl and loosen the adhesive, which could cause bumps or curling.

After cleaning, ensure your flooring is completely dry by going over it with a soft towel. Vinyl is non-absorbent so any leftover liquid will otherwise just sit on the surface in puddles.

For tougher stains, bicarbonate of soda can also be handy with warm water. For even more stubborn stains, for example, wine, a small amount of bleach diluted with water will do wonders. After the product is applied, wipe away with a damp mop or cloth. Any leftover soap scum will develop a film and collect more dirt, so ensure you wipe away thoroughly. Whatever you do, always be gentle while scrubbing and don’t use abrasive cleaners or scourers which could mark the surface.

Luxury Home Builder Can Help You Build A Unique Home Filled With Style

When home improvements go wrong

Once you’ve settled into a home, you will likely want to make any changes which would make it a more comfortable place to live. Unfortunately, there is always a possibility that the planned improvements will go wrong, leaving you worse off than when you started. In such situations, however, you have recourse under the law to get things fixed.

Problems with building work

The law says that any service carried out, including building work, should be done with “reasonable care and skill”, as stated in the Supply of Goods and Services Act 1982. What is “reasonable” can in some cases be a matter of opinion, but in most situations it will be obvious when building work has been carried out to a poor standard.

in most situations it will be obvious when building work has been carried out to a poor standard

Problems can also arise where a builder does something different to what you wanted. You should ensure that you were clear in explaining what the job involved – for example, check your paperwork and any diagrams or drawings which were provided before the work began. If they have failed to do what you hired them for, you can ask them to fix the problem for free.

You will not usually need to pay extra if they have done more work than you asked them to, as you did not agree to have this additional work done. However, in these cases you should check your original contract with the builder, as sometimes they may have stated that in certain situations they may have to do additional work and that the cost would increase accordingly.

Problems with materials

You have the legal right to expect the materials used in building work to be appropriate for the job. According to the law, any items used during construction need to be of satisfactory quality and fit for purpose. “Of satisfactory quality” means that the material in question needs to be well-made and in good condition. “Fit for purpose” means that the items are suited to what they are being used for.

Best Home Builder

As a company this been family owned and operated since 2008 and brings lots of great experience to the table not only build a homes all across but also offer several other construction services for your convenience.

an also provide you with commercial contracting services. This would include things like consulting, office remodels, design build contracting, tenant improvements and so forth. Commercial contracting can involve a wide variety of projects and services, but basically whatever you need done when it comes down to is if you need something built, constructed, remodeled, no matter if it is the commercial sector of the residential sector is large-scale, or small-scale

Do commercial construction and residential construction, a.k.a. home building, but can also do remodeling in any sector as well. This will include things like apartment remodeling or home remodeling. It can be a single portion of your bathroom or can be your entire home gutted from the floor up and re-created looking like a brand-new home. can do any of this and can do all this, no job is too big or too small so if you have any sort of construction project that needs to be done, is the needs to be built

feel that quality of builds, in the affordable rates that provide provide better value than anybody else in the area. Feel that have a better more unique approach to most of the projects that take on, and only that have some incredible incentives and also give back to round out and the things that proud of.

This is objectively true when you look at reviews which you can find a link to on website. While your on the website you can find that a lot of other great information. You can spend a little time getting to know is better on about page and answer lots of great questions like what think makes unique, what were passionate about and so forth

Questions To Ask When Buying A New Build Property

Buying a property on a new build development is hugely appealing to many buyers. Not only do you move into a property that is brand new, with no work to do, most come with a warranty that covers any defects or issues within a certain period of time.

But new home developments do come with worries and concerns just like buying a traditional property, so making sure you know everything about what you’re buying is crucial. Like with any home search, though, remembering all the questions you should ask a developer is easier said than done.

What other developments have you worked on?

When looking at any new development, even by well known, established build companies, always ask for evidence of other work they have completed. If a complete development is within driving distance, take the time to go and see it. If you spot any homeowners while there, ask politely for their experiences with the home builder.

What do I get with my new build?

This might seem like an obvious answer – you’re getting a brand, spanking new home to live in! But buying off plan means your new home is likely to be just a foundation or, at best, the framework of a house – so there’s very little to see. Ask for a list of everything the property includes. What white goods are included and will the garden be landscaped?

What does the new home warranty include?

National House Building Council (NHBC) warranties are applied to more than 80% of new homes built in the and provide buyers with great peace of mind. Most warranties like this apply to the first 10 years after the home is purchased, but it’s worth being aware that NHBC and other warranties are essentially insurance policies – meaning you have to make a claim and a payout is not always guaranteed.

Practical tips for building a high performing home on a budget

Does your client have champagne tastes for comfort but a beer budget for construction of their new home? We’ve got tips for top performance at an affordable price.

Building a house that complies with the strenuous Passive House standard requires a large investment that is off-putting to many margin-conscious home builders.  Many homeowners are keen to lower their home’s carbon footprint and running costs, but often the significant upfront investment of this kind of design is a high hurdle only cleared by the most committed.

However, smart home builders are learning that they can copy high-end constructors to build homes that are incredibly comfortable and energy efficient but are marketable to a broader range of prospective home buyers due to better all-round comfort that includes thermal stability, abundant daylight, great noise suppression and fresh air at an affordable price point. These builders have learnt that they don’t need to blow the budget with commercial grade fixtures if they think critically about the home’s construction and look at the areas where thermal bridges and outside air can compromise the home’s heating and cooling performance, from the floor to the ceiling.

Tape it tight

Study after study has shown that without airtightness, there’s little or no insulation benefit. Identify all the usual leaky spots – windows, door frames, service outlets, foundation-framing seams and roof-framing seams, and get them taped or caulked.

Frame the savings

Consider items such as the framing. Standardising at 600mm centres for framing elements can be a more efficient (and therefore cost-saving) way to install more insulation and less timber without affecting structural performance, plus the electricians and plumbers have fewer pieces of timber to drill through when roughing in.  Smarter techniques include avoiding mass collections of studs in corners and around smaller windows, however check the framing code first to ensure the structure is not compromised.  Any approach to maximise insulation coverage will have obvious acoustic and thermal advantages, creating energy savings and a happier customer.

Look inside

Retrofitting the walls between air-conditioned living spaces and unconditioned garages, laundries, bathrooms and/or underfloor areas can be a long-term homeowner headache but this is often where insulation is of great benefit.  Are you insulating internal walls or raised floors?  Should you add an air barrier?  Insulation, ventilation and construction fabrics in these areas are an easy solution to the common problems of heat and noise transfer from areas such as underfloor, garages, and rooms such as laundry or kitchen.

what to upgrade in your new builder home and what not to!

Are you buying a new home and feel like the builder is asking a lot for the upgrades you want to do? Maybe you need to cut back on the upgrades, but want to make some wise choices about where to invest now and what you can hold off on, to do yourself later.

I’ve got some tips today to help you do just that. I just had a recent Designed in a Click consultation with someone who was wanting to know where would be the best place to put in builder upgrades in her new home.


I’ve seen enough remodeling mess over the years to know that this type of question should be answered with a real look at what it takes to replace or redo something later on down the road.

Here’s my basic rule of thumb…..if it would require a big tear out, expense and mess to replace, spend the money there and get a product you will be happy with for a long time.


Installing a quality flooring product will not only hold up better over time, but it adds value to your property. If you have an open plan house, don’t chop up the flooring materials. People are running quality wood floors into their kitchens these days or are going for wood-look tile if they need even more durability.

Office Moving Company Practices

The Ultimate Office Moving Checklist

The only thing more stressful than a residential move is an office move. Every hour an office is in transit money is lost for the business. Trying to find the time to orchestrate a move while running a business is enough to make anyone overwhelmed.

In addition to giving yourself ample time to plan the move, using checklists is one of the best sanity savers. Use our ultimate office moving checklist to ensure all the major to-dos and minor details are covered.

Scheduling the Move

At least 3+ months before you plan to move:

●      Research local commercial movers.

●      Interview movers and get estimates.

●      Select a mover and lock in a date.

●      Do an inventory of everything in the office you plan to move.

●      Contact your insurance company to discuss whether additional coverage is needed.

Planning the Move

Now that the movers are hired and the date is set it’s time to plan out all of the details. The more effort you put into planning the smoother everything else will go.

●      Create a moving committee at the office and assign specific tasks to each person.

●      Set up the move as you would any other project, including adding it to your project management system.

●      Create a contact list for all employees and companies that are part of the move.

●      Decide whether professional packing services will be needed to help get the office ready for the move. It may be more cost effective than having employees do it.

●      Examine the communication and network system in the new office to decide if any special requirements are needed.

●      Contact service and utility providers to update your service or setup a new plan if necessary.

●      Come up with a strategy for keeping employees, customers, vendors, suppliers and partners updated on the upcoming move. Make sure to send updates to employees the week before and day before the move so everyone knows what is expected.

●      Start looking for the best priced moving supplies and stocking up.

●      Update all accounts with the new address a few weeks before the move.

●      Update your address with the U.S. Postal Service a few days in advance.

●      Contact your moving company a few days before the move to verify all of the details and timeline.

●      Reach out to the building manager of your new office a few days in advance to verify to finalize your moving plans, especially where to load and unload.

●      Update your website and social media accounts with the new address.

●      Use the afternoon before the move to have everyone clear out and pack their desks. Make sure to provide recycling bins.

Moving Office Furniture

If you thought moving living room furniture was a big undertaking, think again. Moving an office full of desks, conference tables and file cabinets will make the living room look like light lifting.

●      Come up with a layout for the new office. Make a blueprint or floor plan to share with the movers.

●      Label the furniture accordingly so the movers know where to put it.

●      Decide which furniture is going to be moved and which furniture needs to be sold or donated.

●      If you’re buying new furniture try to schedule delivery for the day after the move.

●      Get each employee to pack up their own desk the day prior to the move.

●      Have a training day with employees to go over moving safety do’s and don’t’s.

●      Do a demonstration of the proper way to pack up a desk so employees use best practices.

●      Lock or tape up all of the desk drawers.

●      Have tools on hand for dissembling the furniture.

●      Keep bags on hand for the holding hardware that’s removed.

Challenges to Office Moving and What You Can Do About It

Is it time to move already? It seems only yesterday that a group of co-founders sat in this room and officially began the journey to financial freedom. With all those difficulties, smiles and frowns, it is finally time to move. For the most part, it is good news – moving to a new place to accommodate business expansion is what every business startup dreams of. It does, however, come with its fair share of challenges.

According to statistics, 38% clientele for the moving industry comprises corporations moving for business reasons. Even though it is the household utilizing moving services for relocation, most of it seems to happen during summer. 20% of the time, movers are entrusted with the relocation of computers, copiers and other office equipment.

Office relocation is possibly the most challenging move you’ll make. And you need ample pre-planning and thorough management to tackle these challenges effectively.

Productivity Losses

Even if you are a team of five, you’ll need at least two days to pack, move, and unpack everything in your office. It is impossible to not have productivity losses before, during, and immediately after the move.

This is one reason most people use weekends for the move. If by a stroke of good luck, you’re able to find a long weekend on your calendar (if a public holiday fatefully falls right before or after the weekend), this should be the ideal time you make the move.

Benefits Hiring A Moving Company For Your Business Move

As a business owner, you’ll surely have many things to accomplish before the moving day. Since the process requires thorough planning and preparation, enlisting the help of a reliable moving company for your business relocation is undoubtedly priceless. From moving all of your office equipment to unloading them, using professionals usually comes with several benefits.

Less hassle and stress on the employees

Making your employees responsible for the business move may save you more money. However, putting all the responsibilities on their shoulders can be more complicated as they have to know for themselves how to transport large items. Thus, moving your business doesn’t have to be the work of your employees alone. Don’t let them do the tasks on their own to provide less stress and hassle. Remember, your employees are one of your company’s biggest assets, so they should be protected throughout the transition.

Safe moving of the equipment

Again, your office equipment is essential to the operations of your business. That’s why you can’t afford to get them seriously damaged during the move. If you don’t want your equipment and other items to be lost or damaged, hiring commercial movers is the right thing to do. They know how to move electronic equipment and any piece of office furniture with ease and protection. Moreover, they use the right moving and packing equipment that will keep your possessions safe during transit. In case your items may be damaged, or employees may get injured, you have nothing to worry about because most moving companies offer insurance options.

License and insurance

Again, damage or injury will not be a problem if you work with professionals for your business relocation. That’s because they are appropriately licensed and insured. Given such circumstances, you can be sure that the mover will protect your belongings throughout the moving process. You can rest knowing that everything your business owns will be safely transported and in case of accidental damage, they will be insured.

You, Will, not need to rent moving equipment

Without professionals like Movers, you’ll end up renting the moving equipment necessary to transport all of your large items. However, a reliable commercial mover has all the means to provide you with everything your move needs. From the trucks to the packing supplies, crates, and many more, they can let you use these things to make your business relocation smoother and faster. In addition to it, having a moving company on your side can help you and your employees save time in finding all the necessary equipment.

Office relocation checklist guidelines

Office relocation is possibly one of the hardest relocations you will do. This is not to undermine a residential move, but commercial moves bring a new level of stress and a totally new level of responsibility. They bring everything a normal relocation does plus some additional stress and issues. What is this additional stress? The fact that running a business is hard. Anyone who has ever tried knows that one of the biggest keys to success is business continuity. Relocation can jeopardize this continuity and force your work to make a full stop. This is the most dangerous and challenging part for business owners. How do you overcome this? With elaborate planning and with an office relocation checklist.

Believe it or not, something as trivial as a checklist can make a world of difference. And if think it is trivial – you never really tried. To me, it was easily the single most useful tool in the relocation. urge you to heed this advice and pursue having your own office relocation checklist. will offer a few tips and hints on how to make one. Not every checklist is a good checklist. It needs to have all the right elements to it in order for it to rise to its full potential. However, having a checklist does not mean the relocation is done. This is just the beginning. But it is a very important and very good beginning to an otherwise tedious process.

Office relocation checklist – keeping business continuity

The main objective of every office relocation is maintaining business continuity. This is where an office relocation checklist comes into play as an invaluable tool. However, this is not the only tool you will be using. There are many more that you will have to engage. However, today, are talking about the one deem most relevant.

To elaborate, effective planning can change the entire moving process. Especially for an office within which you are trying to have your people still be productive. Anything that can change the flow of work, or bring it to a complete stop is bad news. However, you can overcome this if you anticipate such events happening. If you foresee that the relocation process will bring your production to a stop, you can adequately prepare for it. How do you prepare?

Office relocation checklist elements

The most important elements that your office relocation checklist should contain are the timeboxes as well as the elements you are going to be moving. You are predicting events as well as items that are being moved. The segment that is more relevant is the events themselves. You would need to create a list of all events that could in any way impede your business continuity. This way you have zero surprises. If you are looking to do a commercial relocation DIY, you should probably steer clear away from it

Office Move Tips: Things Learnt During Move

Don’t Rely on your Moving Company to Reconnect Your PCs

Many moving companies offer additional services such as disassembling and reassembling your computers. This may seem like an efficient way to manage costs and resources – but advise against it. This mistake left with over 50% of PCs yet to be assembled, with no contingency or additional staff on hand to assist with setup. This was an unnecessary headache and the only way around it was for project team to input a huge amount of overtime. It’s a mistake will never repeat.

Reach out within your team: Don’t be afraid to reach out to your wider team for help. With detailed instructions and processes in place, a small team of additional helpers can reduce pressure and strain on your IT staff on move day. This will also ensure computers are setup by people familiar with the business and equipment.

Professional IT Services: If you’re managing a large move in a short period of time, recommend hiring professional IT services to assist with install. Professional contractors can help setup quickly and efficiently, especially when working to a detailed floorplan and schedule.

Stage the Move to Eliminate Downtime

If your business is like, with absolutely no room for downtime, advise against moving all departments across during the one day. In case, moved teams in stages to ensure service to clients wasn’t impacted. In a typical business, this might mean moving corporate services such as admin and HR over at the same time, followed by operational staff on a separate day.

Don’t Forget User-Acceptance Testing

Before move day, recommend sending one or two ‘captains’ from each department within the business to test the space. These pilot users will be responsible for assessing their area of the office and reporting any issues before the move.  This process will also allow you to verify that the premises are health and safety complaint before the rest of the team arrives.

Party Planning And Execution With The Help Of Event Planner

How do you make an event successful?

No good marketer shies away from live events. On the contrary, a professionally executed event is often a staple of the successful marketing strategy that turns heads, signs on new clients, helps forge business partnerships, and solidifies brand recognition and loyalty.

Focus On Strong, Future-Looking Content

Do not forget for a moment that your live event is part of your content marketing strategy and you will need to deliver top-quality content to your audience. Whether you are primarily looking to deepen existing relationships or create new ones, betting on strong content is always the way to go.

Placing the focus on exciting future trends is an excellent starting point on your way to great event content. Instead of solely going over what your brand has achieved or what it is doing right now, turn your gaze on what is to come and paint it in intriguing and attractive tones to insure a successful event.

Engagement Pre-, During, And Post-Event

Gone are the days when simply hosting a great live event did the trick. To truly expand your brand in the minds and hearts of your audience, be it other businesses or customers, you need to bring your engagement A-game to the table. Drum up sufficiently high levels of social media buzz before the event. Have some well-crafted social media plugs for the standard channels you use, and always tag your content with a custom hashtag, which you should encourage attendees and fans to use as well.

You probably secured great speakers, so incorporate their own name recognition into your event’s reputation: prepare blurbs from their speeches and accompany those shout outs with appropriate pictures to increase your announcements’ share or retweet potential.

Get Your Tech Levels Right

A successful event is in total sync with its audience’s needs and wants, and technology is a major component in this harmonious relationship. While it is custom to have an electronic agenda, either in mobile-friendly web or app format, how much you pack in there depends on who your audience is. Even though the vast majority of us pack a smartphone (or two) at any given time, not everyone is as happy or able to use it extensively in the context of your event. Plenty of audiences will be happy to have a basic event programme online and then spend the actual event offline, attending to the speakers and taking notes with pen and paper. Others, however, will expect the full digital buffet: interactive, customisable session plan, opportunities to directly engage the speakers via a Twitter wall or another direct communication channel, a custom exhibition stand, a private or public forum for real-time discussions with fellow attendees, and so on. Gauge your audience carefully and build the right kind and amount of tech into your live event!

Collect And Consider Feedback Serisouly

Lastly, get as much audience feedback as possible post-event and make sure it finds its way into your future event planning. Apply an equally high standard to speaker performance and your organisation alike to insure future event success.

Company Goals

Strategic event planning starts with identifying organizational goals and using events to reach those goals. There’s almost nothing that happens in a company that shouldn’t tie back to the company mission. Organizations have clear functions, which is why they require goals and alignment. A few common goals could be:

  • Grow Revenue
  • Build Brand
  • Decrease Organizational Turnover

Align Company Goals and Event Strategy

You know your organization’s goals. That’s a great place to start. If you want to grow revenue, your event should be centered around your product. While a networking happy hour might be fun, it is more likely to increase leads and connections rather than securing closed deals. The type of event you choose to host should align with top company priorities.

Goals and Types of Events

  • Grow Revenue: Trade Show
  • Build Brand: Thought leadership conference
  • Decrease Organizational Turnover: Internal Team Building Event

Promote your event

The next thing to do is to generate an awareness and buzz around the event. This may depend on the objective of the event and whether you’re putting on the event on behalf of someone else, but generally, it is up to you to spread the word and ensure that people attend.

Remember to outline the event in the most engaging way and offer attendees incentives to come (e.g. a talk from an industry expert, an appearance from a celebrity or influences, free food/drink, a goodie bag, etc.).

If your business has a strong social media presence you should leverage that to promote your event. Or, you may choose to harness email marketing or even printed marketing materials like flyers and posters. A mixture of both traditional and online marketing will be effective in garnering a wider interest.

When promoting your event, you should spread the word as early as possible. As events typically have a turn around time of only one or two months, you should give attendees notice as soon as you have a fixed date. Also, always request RSVPs so that you can gauge numbers.

Remember to remind guests about the event in the days leading up to it, either through email, social media, SMS message or an old-school invitation through their door (this depends on a budget allowance and the grandeur of your event).

Tips for How to Make an Event Successful

How do take your event marketing to the next level by generating the necessary hype? Let’s start with content as the first step in how to make an event successful.

1. Maintain a Blog

Setting up a blog is a great way to get people involved in the event before it starts. Create blog posts highlighting the performers, speakers or awardees. Keep the blog focused on the event’s purpose, goals and the benefits. Blogging helps distribute information and create an organic marketing opportunity to help with search engine results. You can promote your informative and entertaining blog content on your social media pages and keep everyone up to date in a creative way. Enlist guest bloggers to help power through the busy times and act as advocates for the event.

2. Get Social

Social media has become king when it comes to event promotion. With over a billion accounts on Facebook and more and more people entering the social media space everyday it would be unwise to ignore it. Automated social media campaigns are great for planned content. You need to keep in contact with your followers, answering questions and staying on top of comments. You can even post videos of the event and guest speakers.

3. Survey Your Guests

What makes for the best promotion is when your guests say positive things about the event. So after the event, reach out to your guests and get them to fill out a short satisfaction survey. This can be easily done through email or on your social media page. If you think your response rate may not be very high, you can include an incentive that guests will receive after completing the survey (like a contest entry or a coupon for a local business). Remember, your guests will always be your best advocates!

4. Location Location Location

Never let anyone say that location doesn’t matter. It does, and if you have a great location you will attract more guests. It doesn’t necessarily have to be the most expensive location. Instead of going for the most popular venue and paying premium prices, try a less popular venue that still offers a great space.

5. Get Organized

You don’t always have a year to plan your big event. But there are ways to help you get through the time crunch when getting your event off the ground. Create an attractive idea which will not only engage fans but also sponsors. Then put together a basic schedule for the event and what needs to be done. Get your speakers or performers selected and signed on, book your location, figure out your ticketing, get your event crisis plan together and get your marketing plan ready. Though it can seem overwhelming, especially for newcomers to the event planning world, if you can make and stick to a event planning schedule, you should have no problem pulling off a legendary event!

How A Personal Injury Lawyer Helps Clients Claim Compensation

What does a personal injury lawyer handle?

What is the role of a personal injury lawyer?

Personal injury lawyers are civil litigators who represent clients – commonly referred to as plaintiffs – alleging psychological or physical injury as result of negligence or careless acts by another person, company, entity, government agency or organization. Personal injury lawyers practice in an area known as tort law. This area of law specializes in civic or private wrongs or injuries, monetary or nonmonetary damages. This includes defamation and actions of bad faith or breach of contract to a person’s reputation, rights or property.

Although personal injury lawyers are armed with licenses to practice in all facets of law, they usually handle cases falling within tort law, such as work injuries, flawed products, accidents caused by slips and falls, road accidents and other related accidents. Personal injury lawyers help their clients secure compensation for losses incurred. These losses include the loss of capacity to earn, inability to perform normal duties, suffering, and pain. They also include expenses that may arise, the loss of companionship, legal costs, emotional distress and attorney fees.

The attorney will ensure clients are safe from being victimized by companies that offer insurance and the established legal system. Personal injury lawyers are often referred to as trial lawyers, although most of their cases are settled before going for a full trial.

What are the duties of a personal injury lawyer?

Personal injury lawyers have many duties in aiding their clients. These duties include both ethical and professional codes of conduct and rules provided for by the associations that license the lawyers. Once the state bar association licenses them to practice law, the lawyers can file complaints in court, argue cases, prepare legal documents and offer professional legal advice to plaintiffs of personal injury.

Personal injury lawyers have the sole responsibility for talking to and interviewing clients and assessing their cases. They further identify the pertinent issues within the client’s case, and thereafter conduct research to build a solid case. The most important professional mandate of a personal injury lawyer is to help clients obtain the compensation and justice they deserve after undergoing losses and suffering. This is done through client counseling, advocacy, legal advice and oral arguments. The case normally heads for trial when both parties fail to reach an amicable settlement.

Personal injury lawyers are expected to follow strict set principles of legal ethics when executing their mandate with clients. While the specified guidelines vary from state to state, each lawyer is expected to evaluate legal issues while exercising due diligence in any legal matter commenced. They owe plaintiffs the onus of confidentiality and allegiance as they work to protect their client’s best interests and not their own.

Discusses Your Claims With Insurance Companies

If you’re in an auto accident both your auto insurance carrier and the other driver’s liability carrier will want to talk to you. If it’s a premises fall or an on-the-job injury, a general liability or workers compensation carrier will want information. They’ll all want recorded statements.

  • To control the flow of information that might undermine your claim, your lawyer will refuse the liability carriers’ requests.
  • As your auto insurance policy and applicable workers compensation carriers require cooperation, your attorney will either arrange and supervise your statement or coach you ahead of time on what to say or not say.
  • Additional conversations with your insurance companies may cover medical bill payments, auto repair, health insurance subrogation rights, and basic liability discussions.

What does a personal injury lawyer handle?

Almost any case a personal injury lawyer handles falls under tort law. In tort cases, the main goal is for an injured person to be compensated financially or “made whole” for all losses stemming from an accident or other incident caused by another person’s carelessness or intentional conduct. In a personal injury lawsuit, the financial compensation is also called “damages.” Personal injury cases are handled by personal injury lawyers in civil court.

In a personal injury claim, the types of damages that are available can vary depending on the type of case, the circumstances of the victim’s injury and state laws. In general, compensation may cover lost wages, present and future medical expenses, pain and suffering, rehabilitation, wrongful death, punitive damages, and more. An experienced personal injury lawyer can help estimate what a case is worth.

Personal injury cases typically involve a private individual filing a civil “complaint” against another person, business, corporation or government agency, alleging that they acted negligently or irresponsibly in connection with an accident or injury that caused harm.

Personal injury covers a wide variety of different situations:

Accidents. Personal injury rules apply in situations where someone acts in a negligent manner, and that carelessness causes harm to another person. Examples include car accidents, workplace accidents, slip and fall accidents, elevator accidents, construction accidents, and medical malpractice, among other types of cases. Personal injury lawyers may also handle workers’ compensation claims.

Intentional Acts. In these situations one person’s intentional conduct causes harm to another person. Examples of intentional acts include assault and battery, sexual assault, and road rage.

How do personal injury lawyers level the playing field?

When you have any kind of injury claim, there is typically an insurance company on the other side.  This puts you at a disadvantage, because:

  • Insurance companies have a large legal department working against you.
  • Their incentive is not to help you.  It’s to pay you the least money possible.

They will use the law against you and find ways to minimize or avoid paying you.  This can include legal loopholes, questionable interpretation of the event that caused your injury, or twisting your own words against you.  If you are not a trained lawyer, it’s very hard to file the right documents to fight them—or even, in some cases, to know what evidence will help you most.

But the equation changes when you have a lawyer of your own.  Your lawyer is your advocate, using the law to help you get the largest financial recovery possible.  They understand the tactics the insurer uses, and how to fight them.  In many cases, simply having a lawyer immediately changes the way you are treated by the insurance company.

Assessing the Situation

A personal injury lawyer can help you determine who is at fault for your injury, and how they should be held responsible. They can help you figure out if you will be dealing with WSIB or an insurance company.

You may not know your rights, or how much compensation you deserve, but a lawyer can help you figure this out, depending on what type of case you have. If you haven’t been through it before, you might not know what to expect from the process, but your lawyer will explain how it all works and help you to understand the timelines, as well what kind of results you should anticipate.

Protection and Sound Advice

A lawyer can ensure you don’t do anything to jeopardize your case, but work towards the best possible results instead. Your lawyer will advise you on legal and ethical issues regarding your injury and accident, providing you with information you might not be able to access anywhere else.

Paperwork, Forms and Evidence

By having a lawyer on your side, all of the relevant evidence will be gathered, the paperwork will be handled, and the witnesses will be interviewed. Your lawyer can tell you the time limitations on filing a suit, which means the sooner you hire a lawyer, the better. Whether your case goes to trial or is settled out of court, having the peace of mind that a lawyer provides is so important.

Personal injury lawyers fight for your rights. By assessing your case and determining the best way to pursue results, your lawyer will make sure you are compensated with dignity.

Posted inLegal